Neopost Si 65 Manualidades De Navidad

• INSERTER IN-3 (SI-92) OPERATOR MANUAL GENERAL The SI-92 is a modular mailing system. For each stage within the mailing process, such as feeding, folding, collating of documents and inserting and sorting of filled envelopes a module is available. In this way SI-92 adapts to the customers' needs.

• CONTENTS Before using this system thoroughly read the operating Section Page Section Page instructions. In the European Union an operator manual FAULT FINDING GENERAL printed in the national language(s) is supplied with the General system. If it is not, contact your authorized distributor. HOW TO USE THE OPERATOR MANUALS 7.1.1 The error screen ACCESSORIES. • bottle envelop slide set brushes (3 pcs.) dust brush mains supply cable press bracket Fig.

2 HOW TO USE THE OPERATOR MANUALS Use the SI-92 manual as the main guide. In the text of this ACCESSORIES manual we will refer to the other operator manuals if This SI-92 manual, existing of two parts, describes the The IN-3 is delivered with the accessories shown in Fig. • envelop hopper insert position user interface sealing area exit Fig. 3 UNDERSTANDING THE MACHINE User interface The service engineer has access to all menus. The system can be started, stopped or cleared by pressing The user interface of the inserter exists of two menus; the Function the concerned key located below the display of the inserter, 'main menu'. 6 Operating controls I: Envelop hopper Power inlet J: Release handle hopper A: Top cover See Fig.

View and Download Neopost INSERTER IN-3 SI-92 operator's manual. Summary of Contents for Neopost INSERTER IN-3 SI-92. Neopost Technologies B.V.

The power inlet B is located at the rear side of the K: Release handle sealing table rollers B: Loc machine. • job number job name job counter preset counter counter Fig. 8 Display keys OPERATING THE SYSTEM If the system is switched off after, for example, a paper stoppage, the brushes will not rest on the watertray.

This Key 1 through 6 Preparations inserter module causes the brushes to dry if usage is interrupted for a longer See Fig. 11 Switching on Entering the personal pin code The main menu Switch on the inserter using the power switch A, see Fig. 10 the pin code screen is shown. The main menu is shown in Fig.

The 'main menu'. 14 5.4.1 Job info screen overview When key 3 is pressed in the “job data” menu the upstream When key 6 is pressed in the upstream (transport) module (transport) module screen is displayed (see Fig.

The screen, the screen in Fig. 15 When key 4 is pressed in the “job data” menu the downstream (sorting) module screen is displayed (see Fig.

The screen shows the following functions: • select a higher job number (key 1). • select a lower job number (key 2). • 5.4.2 Schematic view 10/40 SI-92.

17 5.4.3 Selecting a job 5.4.4 Test run menu In case an FO-3 is used, a screen as shown in fig. 18 will be displayed. The envelope position keys 4 and 5 of figure 17 After pressing key 2 in the 'main menu', the display shows After pressing key 3 in the 'main menu'. 19 Feed one envelope Insert one document Envelope stop position adjustment With this function the proper feed of envelopes can be The flap folding line must be positioned under the green With this function the proper functioning of the whole tested. 20 Envelope fingers adjustment Fine tuning the folder settings The following functions are available: • test for a folded document 1x (key 1).

It makes sense to In SI 92, if and when the electronic folder FO-3 is used, the When the envelope stop position is correct the insert fingers do this in the same menu screen. 22 5.4.5 Counters menu Increase and decrease preset counter 5.4.6 Settings menu By pressing key 4 or key 5 the preset counter will be After pressing key 4 in the 'main menu', the display shows After pressing key 5 in the “main menu”, the screen as the 'change counters'. Program program facut stampile rotunde decorating cupcakes with buttercream. 23 Thickness detection Reset thickness detection Entry to job menu The IN-3 is equipped with a document thickness detector. By pressing key 5 the thickness detection will be reset.

When key 6 in the “main menu” is pressed the display The thickness detector controls the thickness of the shows the screen in Fig. • Operator menu structure Select a job number for job Job data, page 8 data, see page 8 Select (upstream) VersaFeeder 1, 2 Select a job or transport module data Select (downstream) sorter module data Confirm selected job and go to main menu Feed one envelope from hopper A, page 12 Feed one envelope from hopper B Insert one document.

25 Envelope hopper adjustment 5.7.1 Side guides adjustment hopper A 5.7.2 Envelope separation hopper A The IN-3 can be equipped with a second hopper, the EF-3 Take a stack of about 20 envelopes. Fan the envelopes a bit Adjust the envelope separation by turning thumbwheel D see section 10.2 page 32. 26 5.7.3 Side guides hopper B 5.7.4 Envelope separation hopper B Take a stack of about 20 envelopes.